Iscar now offers a family of high-performance slitting tools that join the convenience and security of Tang-Grip clamping with the increased strength of the revolutionary Sumo Tec insert grades.
The perception, already established effective in Tang-Grip parting tools, has now been spread to slitting cutters. In the patented Tang-Grip clamping system, inserts are press-fit into their pockets accompanying a special hand tool, and are clutched tightly in place without the need without requiring clamps, upper jaws or set screws that can weaken the insert and thwart chip flow. The pocket configuration utilizes cutting forces to hold the insert seated solidly in position, eliminating any prospect of insert pull-out. The Tang-Grip clamping system also fosters increased accurate slitting cuts plus lengthened pocket and insert lifespan.
Iscar's Sumo Tec insert grades showcase a specific post-coating treatment which extensively boosts tool life and constancy.
Introduced in late 2007, the completely new Sumo Tec treatment flattens the insert's coated surface to banish microscopic stress raisers, lessen heat and friction and increase chip flow. The result is enhanced toughness and opposition to chipping and built-up edge, all leading to enhanced tool life. The golden-colored side on Sumo Tec inserts aides wear detection. Size for size, Tangslit cutters give more teeth than Iscar's SGSF cutters, providing higher feed rates.
Their better rigidity leads to straighter, additional accurate cuts and lowered vibration even in large-diameter cutters. The brand new Tangslit TGSF cutters come in 100 to 160 mm diameters, 3 and 4 mm widths and can accept the exact same selection of inserts as Tang-Grip parting tools. Several other sizes will be added.
Existing Sumo Tec grades for Tangslit cutters include:
IC808, with a tough submicron substrate below a Sumo Tec TiAlN PVD coating, giving incredible resistance to impact loads and built-up edge. This grade is endorsed for slitting heat resistant alloys, austenitic stainless steel, hard alloys & carbon steel.
IC830, presenting greater toughness for heavier parting and grooving including interrupted cuts. It is suited for every stainless steel & high temperature alloys.
IC908, a hard, fine-grain substrate with incredible chipping resistance, joined with a brand new Sumo Tec TiAlN PVD coating. It is perfect for nodular or grey cast iron.
IC928 and 928A, PVD TiAlN-coated tough grades suitable for stainless steel, high temperature alloys and other alloy steels. These grades are additionally suggested for interrupted cuts and heavy operations.
Every Tangslit and Tang-Grip inserts are found in J- or C-type chipformer geometries from Iscar.
Iscar Adds Their Latest Creations To A Extended Line Of Effective Hole Generating Solutions
Iscar recently released several different drilling innovations to meet their customers needs. These new products are Sumocham Drill, DR-DH and Deep Drills. Drawing off of their experience Iscar has come up with new and innovative ways to increase productivity for the end user.
Some Of Improvements In Carbide Inserts Coming From Iscar From Over The Last Decade
Iscar is introducing a new unique milling system with tangential, clamped, butterfly-shaped LNKX carbide inserts. The butterfly-shaped insert has significant advantages compared to the current flat, square shapes. The new geometry has more cutting edges, positive rake face, reduced cutting forces resulting in higher performance.
The Newest In Carbide Endmill Configuration In A Extended And Outstanding Family From Iscar
Manufacturers and die & mold shops can eliminate chatter problems in many milling operations with Iscar's new Chatterfree endmills. The cutters' variable-pitch flute pattern eliminates harmonic vibration, the main source of chatter. This enables faster cutting and finer finish in rough or finish slotting, shoulder milling and cavity milling.
Original Tools And Carbide Insert Shapes From Iscar To Better Improve The Machining Procedure
Iscar is introducing Penta 34 carbide inserts with a new PB chipformer. The PB chipformer features a single cavity with a positive rake, neutral shoulder angle, and a honed edge. It is actually a C-type chipformer with a different frontal edge.
Push Pull Testing For Railway Industry With Calibrated Gauges. Stress Load Testing Methods For On Site Evidence To Testing Requirements.
Push Pull Testing for the Railway industry for proof of reliable anchor fixings. Calibrated push pull force gauges are used for stress load testing along with tensile strength pull testing procedures. Proof of load testing undertaken, measured, recorded in a reliable and standard way to BS5080 Part 1 standards.
A Number Of Improvements In Carbide Inserts Thanks To Iscar Across The Last Decade
Iscar is announcing a brand new unique milling system that includes tangential, clamped, butterfly-shaped LNKX carbide inserts. The butterfly-shaped insert has meaningful advantages compared to the current flat, square shapes. The new geometry has more cutting edges, positive rake face, decreased cutting forces resulting in better performance.
Commercial Water Heater- Which Is Right For Your Needs
If you are in the market for a commercial water heater then consider what the needed application is and your overall cost to determine which is best for you. Since there are so many to choose from you may have to do some calculating in order to match the need.
Brand-New Car Manufacturing Jobs To Help In Preserving The Overall Economy
The global recession the economy is experiencing in the past few years have pushed major companies to close down and stop their operations.
Related Articles
Blogroll